If I plug in either JVA, the fuse on the board blows.īob told me to test the relays by powering everything down and measuring the resistance at the 24vDC side. I say appears with regards to the relay because if I run anything other than the filter-pump alone, the fuse on the board blows. So I did and to make a long, long story short, it would appear I have at least one bad power relay and possibly one or two bad JVA (Jandy Valve Assembly). Bob suggested that I start plugging in components one-by-one to see what blew the fuse. So after talking with Bob, I unplugged everything on the board, replaced the fuse, powered up and now I have lights on the board. As soon as I applied power, the fuse blew. I had plugged everything into the board when it arrived thinking we were good to go. Assuming of course, the CPU board is ok.įollow-up on the repaired board: Bob at BPEngineering ( ) has been great in helping me troubleshoot this nightmare.Īs I have found out, there is apparently more wrong in this power-center than just a bad board. It will be almost 3 weeks with no filtering (been dumping in the bleach and muriatic acid) by the time this thing gets fixed. I just wished I could find out if I can get away with, temporarily, energizing the filter-pump relay to get the water moving. So like Rossterman above, I'm going to send in my board, get it repaired and then start saving my Benjamins to buy some other company's controller because I'm done with Jandy/Zodiac or whatever these guys are called this week. Jandy finally called me back this evening (around 20:00 CDT believe it or not) and after talking with the gent on the other end I get asked two questions:ġ) How old is the panel (just under 3 yrs)? To which he mumbled under his breath, "yeah, that's about right."Ģ) Am I licensed pool professional? (nope) To which he responded, "Well, that's too bad because you are going to need a new board and if you install it instead of a licensed pool professional, then you automatically void the warranty." "Oh, and I can't tell you anything about the installation procedure. I was just getting ready to post that very same link!!! (although I don't feel any better unfortunately.) IF anyone were to ask me what company I would recommend for pool equipment, I would tell them to RUN, RUN, RUN away from Jandy-assuming there is another choice. LED lighting, starting condensers, filters, and now the power-panel. We bought the house just over a year ago and we have had nothing but problems with any part that has JANDY written on it. I don't hold out much hope and would really like to figure out a way to bypass the panel altogether just to get the filter-pump working. I'm now in the queue at Jandy for them to call me back. I've pressed the reset button so many times I think I have actually punctured the little rubber seal over it. I have checked the fuse, checked the new transformer output (25.2volts) and even replaced the 2032 batter on the circuit board. Unfortunately, I still have no power to the panel. I got it today (I only live 100 miles or so from where he is located). He was the least expensive I could find and he did ship as soon as the PayPal payment hit. So I bit the bullet and ordered a new transformer from here: While I did end up finding a transformer rated 60VA, Class2, Class 3, it was almost as expensive as the official Jandy Replacement. An equivalent output transformer, 60VA or higher, is almost $100. I would really appreciate hearing from others who may have had this experience or ideas to fix it quickly and get the pump working again.As I have found out, the main reason these transformers are so expensive is the 2.5A output. I left the power to the pump on all night hoping that it might resolve itself, but it didn't. I reset the circuit breaker last night, but the same happened: Power LED is on, nothing else works. Besides the Power LED Indicator, none of the other Control Panel buttons are responsive. I then pressed the Start/Stop Button, but nothing happened. When I went back to start the pump, I first turned on the wall switch and noticed that the Power LED Indicator on the Control Panel turned on. In the morning our pool water level was low, so when I heard gargling in the skimmer at the programmed start time of the pump, I walked over to the pump, pressed the Start/Stop button to shut it off, and also turned off a wall switch I have for the pump so that someone else wouldn't start it later. Yesterday, however, we discovered a problem. We have a Pentair Superflo VS pump that was installed 6 weeks ago and had been working flawlessly since installation.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |